Details of some Applications

Blower For Agitation

Ring Blowers are great for applications requiring agitation of fluids in plating tanks, rinsing tanks and cleaning tanks because they offer the following advantages

  • Clean, oil-free air without contaminants to foul or spoil the fluid.
  • Low noise levels meet requirements without costly noise reduction equipment required by positive displacement Roots-type blowers.
  • Low operating cost when compared to air compressors.
  • Low purchase cost when compared to other types of blowers or compressors.
  • Dependability of a rotating machine without wearing, rubbing or sliding components. The only moving part is a non-contacting impeller supported by two high quality ball bearings.

a) Plating Tank

Ring blower produce agitation that helps renew cathode films, decrease polarization, and allow the use of higher current density, permitting higher plating speeds and finer grain deposits. The air agitation’s scrubbing action also minimizes the quantity of rinse water needed, thus reducing the load on water treatment facilities.

b) Cleaning Tank

End solvent / solution stagnation. With a Ring blower agitation, fresh solution is constantly brought into contact with the part, removing dirt particles and dissolving grease.

Blower in Place of Vacuum Pump

The robustness and the reliability of our Blowers are very much appreciated for this application. Particularly for the vacuum application of pneumatic conveying in vacuum because Ring Blower used to create a vacuum are less sensitive to the possible passage of conveyed particles., than other technologies.

Blower For Water & Waste Water, Effluent, Sewage Treatment Plants

RAICO offers Ring Blower for a cost of applications in water and wastewater applications. As a market leader in this field RAICO has been approved by the leading engineering companies. RAICO has been a pioneer in introducing the next evolution of blower design, offering greater efficiencies, and blower cost of ownership and maximize total energy savings, not just the mechanical efficiency of the blower.

One of the important equipment in any effluent treatment plant or wastewater treatment plant is the oil-free low-pressure air blowers, which are used for many applications & processes like: Diffused aeration. Filter backwashing. Proper selection of Blowers can save energy cost up to 60%.

Proper aeration and blower selection are two of the most important considerations at a wastewater plant. Energy consumption for Aeration at wastewater treatment plants typically consumes 60% of all electrical usage. Blowers can offset some of the energy requirements. To ensure the most effective results, select the proper size, type and layout of blower equipment.

These Ring Blowers are used for many applications such as

  • Basin Aeration
  • Digester Gas
  • Wastewater Treatment
  • Air Scouring
  • Filter Backwash Systems
  • SBR / MBR
  • Grit Chamber Aeration
  • Lagoon Aeration

The function of the Blower, for this application, is to supply air to one or several tanks in order to bring oxygen to bacteria which must degrade the organic matter. To inject this air, the blower must overcome the resistance, or backpressure due to the water height and diffuser / piping losses. As the effluent quantity to be treated changes over the course of time, it is desirable to inject only the amount of oxygen necessary and in sufficient quantities to optimize the oxygen needs of the bacteria, thus making it imperative to have the ability to vary the flow while keeping a constant pressure. The Multistage Blowers allows variation of the flow, by a simple flow regulation valve, located at the outlet, and therefore energy consumption is in proportion to the actual flow point, thereby optimizing performance and minimizing power consumption at all operating conditions.

The Multistage Blowers offers the following advantages:

  • Clean and dry, oil free high-pressure air without pulsation
  • Wide flow operation range while maintaining a constant pressure
  • Reliable and robust machines thanks to their simple design
  • Cast construction for continuous duty service
  • Low maintenance costs
  • Very low sound level in compliance with standards

Blower for Pneumatic Conveying Systems

When bulk goods need to be conveyed gently from A to B, segregation-free and without break-up, a variety of pneumatic conveying systems can be used, dependent on the application, such as suction conveying systems, pressure conveying systems, suction-pressure conveying systems, impulse conveying systems or dense-phase conveying systems.

Pneumatic conveying (the transfer of dry bulk products such as flour and plastic pellets through a pipe line) has been one of the major uses for Ring blowers and one in which RAICO has developed much engineering expertise.

Blower For Printing

RAICO offers one of the largest selections of blowers. Our products cover the full range, from small centrifugal blowers all the way up to large industrial Ring Blowers. You can count on RAICO to meet your air handling needs. Applications for printing machines, copiers, collators, and book binding machines include blowers for

  • Paper Handling
  • Pick-up
  • Feed
  • Transport
  • Separate
  • Toner Control
  • Ink Drying
  • Laser Imaging
  • Cleaning Systems
  • Cooling
Blower For Food Processing

Fresh produce needs to be cleaned before it can be placed in market. Blowers provide very economical & efficient cleaning of fresh produce by agitating water bath in which produce can be placed for cleaning. Powerful agitation of water is gentle to the produce, so no harm comes to its texture.

Blower For Personal Cleaning

Blowers provide very effective, safe, efficient and economical solution for personal cleaning.

Blowers For Dust Protection

Blowers are used for dust protection & cooling of opacity sensors, video camera lens etc.

Blower For Efficient Furnace Fuel Burning

These blowers deliver higher pressure compared to centrifugal blower, making it possible to improve fuel to air mixing, leading to very effective fuel burning.
Integration with VFD makes furnace temperature control very easy.

High pressure blowers with inlet air temperature below 70deg. C. and direct mounting are compact in construction and run with high-speed motors.  Such blowers are mostly used for better mixing of fresh air to the furnace for a better combustion.

Blower For Drying / Debris Removal With Air Knife

These blowers are ideal for use along with Air Knifes for drying & debris removal in bottling, ink jet coding, packaging, labeling, sleeving and similar applications. They deliver results at much lesser capital & operating costs. Lower rotational speed of impeller, reduces noise level & offers maintenance free long & continuous life